The heating equipment is equipped with an autodiagnostic function
Подключение диагностического прибора к центральному разъему автомобиля позволяет выполнить следующие операции
- Идентификация
- Считывание кодов неисправности, занесенных в память
- Измерения параметров
- Проверка приводов
- Регулировка CO2
Обнаружение ошибок
The equipment stops automatically after a fault has been detected
Operating the control again (independent heating) or switching off the ignition and starting the engine again (additional heating) involves restarting the heating
If the fault is still present, the heating stops again
If it has been corrected or has disappeared it remains stored in the memory of the equipment and disappears of its own accord after 40 restarts
After 6 faults recorded (without operation at full speed) or Overheating fault recorded, the equipment locks automatically
In this case restarting the equipment is impossible, it is imperative to process then clear the stored faults
Permanent fault detected, the fault is detected at each attempt at starting
Intermittent fault detected, the fault remains stored in the ECU but is no longer detected at each starting test
Чтение параметров
The diagnostic equipment provides the opportunity to read operating parameters with the heating either off or on
In the second case the equipment automatically starts the heating and keeps it operating for 8.5 mn
Screen variables
| параметры, выводимые на дисплей | values read on the diagnostic equipment screen |
|---|---|
| температура охлаждающей жидкости | от -40 °C до 150 °C |
| Напряжение питания | от 10.5 V до 15 V |
| частота вращения воздушной турбины | от 0 до 100 % |
| fuel pump rate | от 0 до 100 % |
| glow plug rate | 0 или 100 % |
Status screen
| параметры, выводимые на дисплей | values read on the diagnostic equipment screen |
|---|---|
| положение | not started или elect. test OK или двигатель запущен OK |
| обогрев | on or off |
| пламя | detected or not detected |
| топливный насос | on or off |
| свеча накаливания | on or off |
| воздушная турбина | on or off |
Регулировка CO2
The diagnostic equipment enables an adjustment of the CO2 issued by the equipment to be carried out
This adjustment is made by modifying the value of a parameter of the ECU memory which affects the speed of rotation of the air impeller
Контроль и регулировка содержания CO2 в отработавших газах требуются в следующих случаях
- Демонтаж блока отопителя
- Замена одного из элементов блока отопителя
- Плохое сгорание, выбросы дыма после запуска двигателя (по прошествию 200 секунд)
Diesel additional heating CO2 adjustment values
| altitude (m) | - 20 | 0 | 20 |
| 1500 | 10,2 - 12,4 | 10,4 - 12,7 | 10,5 - 12,9 |
| 1000 | 9,5 - 11,7 | 9,7 - 11,9 | 9,9 - 12,1 |
| 500 | 8,9 - 10,9 | 9,1 - 11,1 | 9,3 - 11,0 |
| 250 | 8,6 - 10,6 | 8,1 - 10,8 | 9,0 - 11,0 |
| 0 | 8,4 -10,2 | 8,6 - 10,5 | 8,7 - 10,7 |
Petrol independent heating CO2 adjustment values
| altitude (m) | - 20 | 0 | 20 |
| 1500 | 9,2 - 11,2 | 7,4 - 11,4 | 9,5 - 11,7 |
| 1000 | 8,6 - 10,6 | 8,7 - 10,7 | 8,9 - 10,9 |
| 500 | 8,1 - 9,9 | 8,2 - 10,0 | 8,4 - 10,2 |
| 250 | 7,8 - 9,6 | 7,9 - 9,7 | 8,1 - 9,9 |
| 0 | 7,6 - 9,2 | 7,7 - 9,5 | 7,9 - 9,7 |